Author: Bruce Zheng, Co-Founder and Valve Engineer at NTGD Knife Gate Valve
Last Updated: June 8, 2026
Quick Answer: Does a Knife Gate Valve Have a Flow Direction?
Yes, many knife gate valves have a required or preferred flow direction, but the correct answer depends on the valve design, seat arrangement, pressure direction and manufacturer instructions.
Before installation, the key issue is not only whether the pipeline flow arrow points left or right. The installer should also check whether the valve body arrow, “SEAT” marking, seat side, P&ID flow arrow and closed-valve pressure direction all support the same installation decision. If these items conflict, installing the valve without confirmation can reduce shutoff performance, cause leakage, create commissioning problems or require rework.
For a unidirectional knife gate valve, the installation direction is often tied to the seat side, body arrow, “SEAT” marking and the direction of differential pressure when the valve is closed. In many cases, the valve is designed so pressure helps push the gate against the seat. For a bidirectional knife gate valve, shutoff may be possible from both directions, but this does not always mean the valve can be installed without checking the drawing, datasheet or IOM manual.
This article is not a full knife gate valve installation manual. It is a direction-check guide for confirming the correct knife gate valve flow direction, seat side, pressure direction and installation orientation before installation.
Why the Flow Arrow Does Not Always Mean Simple Pipeline Flow
A common and costly mistake is assuming the cast arrow on a knife gate valve body always indicates the normal pipeline flow direction. For many general-purpose industrial valves, this is often how the arrow is interpreted. With knife gate valves, however, the arrow may also relate to the sealing side, the required pressure direction during shutoff or a manufacturer-specific installation rule.
A knife gate valve uses a sliding gate or blade that moves across the flow path. The shutoff performance depends on how the gate contacts the seat and how pressure acts on the gate when the valve is closed. This is why the normal process flow direction and the pressure direction during shutoff should both be reviewed.
In some systems, normal flow and closed-valve pressure act in the same direction. In other systems, such as pump isolation, dead-end service, reverse pressure, silo discharge or slurry service, the pressure direction during shutoff may not be the same as the normal pipeline flow direction.
Body Arrow vs Normal Pipeline Flow
The body arrow may indicate:
- the normal recommended flow direction;
- the side where pressure should act when the valve is closed;
- the direction related to the seat side;
- a manufacturer-specific installation rule.
Because of this, the body arrow should not be checked alone. It should be read together with the valve tag, datasheet, general arrangement drawing, IOM manual and pipeline flow arrow on the P&ID.
If the body arrow and the P&ID flow arrow appear to conflict, do not decide by appearance alone. Confirm whether the valve arrow refers to normal flow, seat-side orientation or the preferred pressure direction specified by the manufacturer.

When Pressure Direction Matters More Than Normal Flow
Pressure direction becomes especially important when the valve is closed. For a unidirectional sealing design, the valve may rely on differential pressure to help the gate seal against the seat. If the valve is installed in the wrong direction, pressure may act on the wrong side of the gate, reducing shutoff performance.
To determine the closed-valve pressure direction, consider the worst-case shutoff condition: which side of the valve will have higher pressure when the valve is fully closed? This may be different from the normal operating flow.
Examples include:
- in pump isolation service, pressure may remain on the pump side, tank side or both sides depending on the system layout;
- in dead-end service, pressure may act from only one side when the valve is closed;
- in systems with possible backflow, pump trip or reverse pressure, pressure may act from either side;
- in hopper or silo discharge service, solids behavior may also affect the preferred orientation.
When shutoff differential pressure does not match normal pipeline flow, the pressure direction should be treated as a primary installation check, especially for unidirectional knife gate valves where seat loading affects shutoff.
Flow Direction, Seat Side and Pressure Direction Comparison
| Concept | What it means | What to check | Why it matters | Common mistake |
|---|---|---|---|---|
| Pipeline flow direction | The normal direction of media flow in the pipe | P&ID, pipeline arrow, process drawing | Shows normal operating flow | Assuming this alone defines valve installation direction |
| Body arrow | Marking cast or tagged on the valve body | Valve body, datasheet, IOM | May indicate recommended flow, seat orientation or pressure direction | Assuming the arrow always means simple pipeline flow |
| Seat side | Side where the seat or sealing side is located or marked | “SEAT” or “SEAT SIDE” marking, drawing, IOM | Helps determine where pressure should act for shutoff | Assuming seat side is always upstream or downstream |
| Pressure direction | Direction of differential pressure when the valve is closed | Process condition, shutoff scenario, reverse pressure | Critical for shutoff in many unidirectional valves | Ignoring reverse pressure or assuming normal flow equals shutoff pressure |
| Preferred direction | Manufacturer-recommended installation direction | IOM, datasheet, valve tag | May depend on valve design, seat type and service | Treating bidirectional valves as document-free |
| Physical orientation | Stem, actuator and valve body position | Installation drawing, pipe position, site layout | Affects support, alignment and solids behavior | Checking flow arrow but ignoring actuator support |
A reliable direction decision should connect all six concepts. If pipeline flow, pressure direction, body arrow and seat side do not point to the same conclusion, the valve should be checked against the IOM or drawing before installation.
Seat Side and SEAT Marking: What They Mean Before Installation
The seat side of a knife gate valve is the side where the valve seat or sealing surface is located, or the side identified by a “SEAT” or “SEAT SIDE” marking on the valve body. This marking is important because it may show the side against which the gate is intended to seal.
In many unidirectional knife gate valves, pressure should act in a way that helps the gate close against the seat. If the seat side is installed incorrectly, the valve may still move open and closed, but shutoff performance can be reduced.
What “SEAT” or “SEAT SIDE” Marking Indicates
A “SEAT” or “SEAT SIDE” marking can indicate the location of the sealing side. Before installation, the installer should confirm:
- where the seat side is marked on the valve body;
- whether the valve is unidirectional or bidirectional;
- whether the datasheet identifies a preferred flow or pressure direction;
- whether the IOM manual gives a specific upstream or downstream instruction;
- whether the application has reverse pressure or dead-end pressure.
The marking is not a substitute for the valve documentation. It is one of several checks that must be reviewed together.
If the SEAT marking is missing, damaged, painted over or unclear, do not guess the direction based only on the valve appearance. Check the valve drawing, seat orientation diagram, datasheet or IOM manual before installation.

For a manufacturer IOM example of SEAT marking and pressure-against-seat orientation, see the Bray Series 941 unidirectional knife gate valve IOM.
Seat Side, Sealing Side and Pressure-Assisted Shutoff
The seat side matters because shutoff depends on gate-to-seat contact. In a directional design, pressure may help press the gate into the seat. This can improve shutoff when the valve is installed correctly. If pressure acts from the wrong side, the gate may not load the seat as intended.
This is why seat side should be understood as an installation-direction concept, not only as a valve part name.
Should the Seat Side Be Upstream or Downstream?
There is no safe universal answer for all knife gate valves.
In many unidirectional designs, the manufacturer may specify the seat side on the downstream or lower-pressure side so that upstream pressure helps push the gate against the seat. However, this should be treated as a common design logic, not a universal rule for every knife gate valve.
For resilient-seated, perimeter-seated, dual-seat or sleeve-like designs, the seat-side logic may differ. In hopper, silo, slurry or reverse-pressure applications, the preferred orientation may also be affected by solids movement, pressure direction or seat protection.
The practical decision path is:
- Locate the SEAT or SEAT SIDE marking.
- Check whether the valve is unidirectional or bidirectional.
- Confirm the normal flow direction and closed-valve pressure direction.
- Compare the valve marking with the datasheet, drawing and IOM manual.
- If upstream / downstream orientation is still unclear, confirm with the manufacturer before installation.
Do not assume upstream or downstream from general valve experience. Knife gate valve seat-side logic is design-dependent.
Seat Design Can Change Direction Logic
| Seat / sealing design | Direction implication | How to handle it in selection or installation |
|---|---|---|
| Unidirectional metal seat | Often direction-sensitive | Confirm body arrow, SEAT marking and pressure direction |
| Unidirectional resilient seat | Usually still requires direction confirmation | Check whether pressure must act against the seat |
| Bidirectional resilient or perimeter seat | May seal from both directions | Confirm whether preferred direction still exists |
| Dual-seat or sleeve-like design | Direction logic may differ from one-side seat designs | Do not apply a simple one-seat rule |
| Special slurry or solids service | Direction may affect wear, settling or seat protection | Confirm service-specific installation notes |
Unidirectional vs Bidirectional Knife Gate Valve Installation Direction
Knife gate valves are often described as unidirectional or bidirectional, but these terms must be used carefully in installation planning.
A unidirectional knife gate valve is designed to provide shutoff in one intended direction. A bidirectional knife gate valve may provide shutoff from both sides. However, bidirectional shutoff does not always remove the need to check preferred flow direction, pressure direction or installation orientation.

Unidirectional Knife Gate Valve Installation Direction
For a unidirectional knife gate valve, direction checks are critical. Before installation, confirm:
- the body arrow;
- the “SEAT” or “SEAT SIDE” marking;
- the normal pipeline flow direction;
- the closed-valve pressure direction;
- whether reverse pressure can occur;
- the manufacturer’s installation instructions;
- the valve tag, datasheet and drawing.
The key question is not only “Which way does the fluid normally flow?” It is also “Which side should pressure act on when the valve is closed?”
If the normal flow direction and shutoff pressure direction differ, the unidirectional valve must be reviewed carefully before installation.
For product-level specification context, review NTGD’s unidirectional knife gate valve before selecting a one-way shutoff design.
Bidirectional Knife Gate Valve Installation Direction
A bidirectional knife gate valve may seal in both directions, but it should not be treated as direction-free without checking the documentation. Some bidirectional designs still have a preferred direction because of the seat arrangement, wear components, gate design, slurry behavior, actuator support or application requirements.
For example, a bidirectional knife gate valve used in clean water service may be less sensitive to installation direction than a valve used in abrasive slurry, vertical discharge, hopper service or reverse-pressure isolation.
For reverse-pressure or two-way shutoff applications, compare the installation requirement with NTGD’s bidirectional knife gate valve product page.
Why Bidirectional Does Not Always Mean Document-Free Installation
Bidirectional shutoff means the valve can seal from both directions under specified conditions. It does not automatically mean:
- every physical installation orientation is acceptable;
- actuator support can be ignored;
- solids behavior does not matter;
- forward and reverse pressure conditions are always identical;
- the IOM manual can be skipped.
In slurry service, an incorrect orientation can still increase solids accumulation or uneven seat wear. In dead-end service or reverse-pressure systems, the pressure side still needs to be checked. On large valves with pneumatic, hydraulic or electric actuators, actuator support may still be required even if the valve is bidirectional.
For an example of a bidirectional knife gate valve manual that still discusses preferred flow and pressure direction, see the WEY Knife Gate Valves instruction manual.
Unidirectional vs Bidirectional Installation Direction Logic
| Valve design | Direction logic | Seat / sealing behavior | What to confirm | Boundary / bridge direction |
|---|---|---|---|---|
| Unidirectional knife gate valve | Direction-sensitive | Seals in one intended direction | Body arrow, SEAT marking, pressure direction, IOM | Product page should carry product details |
| Bidirectional knife gate valve | May allow shutoff from both directions | Seals from either side under specified conditions | Preferred direction, seat type, pressure rating, application | Product page should carry selection details |
| Resilient / perimeter seat design | May improve bidirectional sealing | Seat may contact the gate around the perimeter | Whether the design is truly bidirectional | Do not turn this article into a seat product guide |
| Metal seat design | Often more dependent on pressure and seat side | Gate-to-seat contact is critical | Leakage class, pressure side, IOM | Keep explanation focused on direction |
| Severe slurry / solids service | Direction and orientation can affect wear and accumulation | Solids may settle around gate or seat | Flow, pressure, solids, actuator support | Application pages can handle deeper service detail |
Use this table as a direction logic guide, not as a replacement for the valve manual. Product selection details, pressure limits, seat materials and actuator options should still be confirmed on the specific product page or specification sheet.
If the project needs a broader design comparison beyond installation direction, review the existing guide on bi-directional vs uni-directional knife gate valves.
Installation Orientation: Vertical, Horizontal and Actuator Support Checks
Flow direction is not the only installation direction issue. Physical orientation is an extension of installation-direction checking, not a separate installation procedure.
A knife gate valve may be installed in a horizontal pipeline, vertical pipeline, inclined position or under a hopper. The recommended orientation depends on valve size, actuator type, service media, pipe layout and manufacturer instructions.
Vertical Installation in Horizontal Pipelines
Many knife gate valves are commonly installed with the stem or actuator upward when mounted in a horizontal pipeline. This orientation can help with:
- gate alignment;
- actuator stability;
- service access;
- solids behavior;
- packing and stem loading.
However, “actuator upward” should still be confirmed with the valve documentation. Large-bore valves, heavy pneumatic or hydraulic actuators, extended yokes and slurry service may require additional support or a manufacturer-approved orientation.
Horizontal or Inclined Valve Positions
Horizontal or inclined installation may be possible for some knife gate valves, but it should be checked carefully. In a non-vertical position, the gate, stem, yoke or actuator may experience side load. This can affect alignment, operating torque and service life.
If a valve is installed with the actuator horizontal, the site should confirm whether the actuator needs external support. Without support, the valve body, stem or actuator assembly may be exposed to bending load or vibration.
Actuator, Stem and Yoke Support
Actuator support is especially important for:
- large-diameter knife gate valves;
- pneumatic cylinder actuators;
- hydraulic actuators;
- electric actuators;
- extended yokes;
- horizontal stem orientation;
- vibrating pipelines;
- slurry or high-solids service.
This article does not provide structural support calculations. It only flags actuator orientation as a direction-check item before installation.
When actuator weight or horizontal mounting is a concern, pair the direction review with NTGD’s guide to knife gate valve actuation options.
Slurry, Solids and Hopper Service Notes
In slurry, wastewater, mining, tailings, pulp or hopper applications, installation orientation can affect solids accumulation around the gate or seat. If solids settle in the wrong area, the gate may not close fully, operating torque may increase, and seat wear may accelerate.
Where possible, the preferred orientation should reduce the chance of solids trapping near the gate, seat or packing area. In hopper or silo discharge service, the seat-side and pressure-direction logic can be application-specific, so the manufacturer’s installation notes should be checked instead of applying a standard pipeline rule.
For these services, confirm both:
- flow / pressure direction;
- physical installation orientation.
Do not assume that a valve suitable for clean liquid service can be installed the same way in slurry or high-solids service.
For high-solids service where orientation and accumulation risk are important, also review NTGD’s slurry and high-solids knife gate valve selection guide.
Installation Direction Checklist Before Installing a Knife Gate Valve
Use the following checklist before installing a knife gate valve. This is not a full installation procedure. It is a direction-confirmation checklist.

| Check item | Where to verify | Why it matters | Action before installation |
|---|---|---|---|
| Body arrow | Valve body | May indicate recommended flow, pressure direction or seat orientation | Note the arrow direction and compare it with P&ID flow arrow, datasheet and IOM |
| “SEAT” / “SEAT SIDE” marking | Valve body, casting, tag | Identifies sealing side | Locate the marking and confirm it with the drawing or datasheet |
| Valve tag / model | Nameplate, purchase record | Confirms design type | Verify whether the valve is unidirectional, bidirectional or special-service design |
| Datasheet | Manufacturer document | Defines pressure, seat and design limits | Check preferred direction notes and seat type |
| IOM manual | Manufacturer instruction | Gives installation-specific rules | Use the correct manual for the specific valve series or design |
| GA drawing / installation drawing | Project or manufacturer drawing | Shows intended orientation | Compare drawing orientation with site pipe layout |
| P&ID / pipeline flow arrow | Engineering drawing | Shows normal flow direction | Compare process flow with valve body arrow |
| Normal flow direction | Process condition | Shows usual operating flow | Do not confuse it with closed-valve pressure direction |
| Closed-valve differential pressure | Process condition | Determines pressure direction during shutoff | Identify the worst-case shutoff condition before installation |
| Reverse pressure possibility | System design | May affect seat loading | Confirm whether bidirectional sealing or reverse pressure rating is required |
| Seat type | Datasheet or drawing | Affects sealing direction | Check whether the seat is metal, resilient, perimeter, sleeve-style or dual-seat |
| Unidirectional / bidirectional design | Product type and datasheet | Defines direction sensitivity | Do not assume direction logic from appearance |
| Vertical / horizontal installation | Pipe layout and IOM | Affects gate alignment and actuator support | Confirm recommended orientation before mounting |
| Actuator support | Site layout and IOM | Prevents side load and premature wear | Verify whether external support brackets are required |
| Slurry / solids / hopper service | Process description | Solids can affect closing and wear | Review service-specific installation notes |
A good installation-direction review should answer three questions before the valve is installed:
- Which way does the media normally flow?
- Which way will pressure act when the valve is closed?
- Which side of the valve is designed to seal under that condition?

If these three answers do not match the body arrow, SEAT marking and documents, stop and confirm before installation. If the conflict cannot be resolved on site, provide the valve tag, drawing, P&ID and process conditions to NTGD for application or specification review before proceeding.
What Can Happen If the Flow Direction or Seat Side Is Wrong?
Installing a knife gate valve in the wrong direction may not cause immediate visible failure, but it can reduce shutoff performance, increase maintenance workload and create commissioning problems. In process isolation service, pump isolation, tank isolation or slurry handling, the consequence may include leakage, repeated adjustment, unplanned inspection or early valve damage.
The exact risk level depends on the valve design, operating pressure, media abrasiveness, solids content, actuator arrangement and operating frequency.

Leakage and Poor Shutoff
The most common risk is leakage across the seat. If pressure does not help the gate seal against the intended seat side, the valve may not achieve the expected shutoff. This is especially important in unidirectional designs.
Poor shutoff can also occur when solids collect near the seat or when reverse pressure acts from an unexpected side.
Gate, Seat and Packing Stress
Wrong orientation can increase uneven loading on the gate and seat. Over time, this can contribute to:
- seat wear;
- gate edge wear;
- packing stress;
- higher friction;
- uneven sealing contact.
If the actuator or stem is unsupported in a non-recommended orientation, side load can also affect packing and stem alignment.
High Torque or Gate Movement Problems
A wrongly oriented valve may become harder to operate. Symptoms may include:
- high operating torque;
- gate not seating fully;
- gate binding;
- slow actuator movement;
- difficulty opening or closing;
- repeated adjustment needs.
These symptoms do not always mean the valve is defective. They may indicate that the flow direction, pressure direction or physical orientation should be rechecked.
Wrong Direction / Wrong Orientation Risk Matrix
| Risk | Possible cause | Typical symptom | What to re-check |
|---|---|---|---|
| Seat leakage | Pressure acting from wrong side | Leakage when closed | Seat side, pressure direction, IOM |
| Poor shutoff | Gate not loaded against seat as intended | Valve does not isolate fully | Body arrow, SEAT marking |
| Gate not seating | Solids or wrong pressure direction | Gate stops before full close | Media, solids, seat area, direction |
| High operating torque | Side load, solids, misalignment | Hard manual operation or actuator overload | Orientation, actuator support, pipeline alignment |
| Gate / seat wear | Abrasive media or wrong loading | Shorter service life | Flow direction, seat type, slurry condition |
| Gate damage | Incorrect pressure or mechanical stress | Deformed or scored gate | Installation direction, pressure direction |
| Packing stress | Stem or actuator side load | External leakage near packing | Actuator support, stem orientation |
| Actuator / stem side load | Unsupported horizontal actuator | Vibration, bending, uneven movement | Support bracket, mounting position |
| Solids accumulation | Poor orientation in slurry or hopper service | Gate cannot close cleanly | Flow path, discharge direction, solids behavior |
| Misalignment | Pipeline or installation stress | Uneven operation | Pipe alignment, flange parallelism |
| Premature valve failure | Combined wrong direction and poor support | Repeated leakage or operation problems | Full direction checklist |
This risk matrix is not a troubleshooting manual. It is a reminder that direction errors can create symptoms that look like seat, actuator or packing problems. Completing the direction checklist before installation can reduce the risk of leakage, operation problems and rework during commissioning.
What to Confirm with NTGD Before Final Selection or RFQ
If the correct knife gate valve flow direction, pressure direction or installation orientation is not clear, confirm the application before final valve selection or RFQ. Size and pressure class are basic requirements, but direction-related details often determine whether a unidirectional or bidirectional design is suitable for the actual service.
The review should focus on how the valve will seal when closed, where pressure will act, how solids will behave and whether the installation position creates actuator or stem support concerns.

For project-level selection support, NTGD’s knife gate valve manufacturer page provides the main product and specification review bridge.
Information Needed for Direction Confirmation
| Information | Why it matters for direction | Example to provide |
|---|---|---|
| Valve type | Determines directional sensitivity | Unidirectional or bidirectional |
| Normal flow direction | Shows process flow | Left to right, bottom to top, tank to pump |
| Closed-valve pressure direction | Shows shutoff load | Pressure from upstream, downstream or both sides |
| Reverse pressure possibility | Determines whether bidirectional shutoff is needed | Backflow, pump trip, dead-end service |
| Media | Affects seat and wear behavior | Water, slurry, pulp, wastewater, tailings |
| Solids content | Affects gate closing and accumulation | Fiber, sand, sludge, ore particles |
| Pressure and temperature | Defines operating limits | Working pressure, shutoff pressure, design temperature |
| Seat type | Affects sealing direction | Metal, resilient, perimeter, sleeve-style |
| Body material | Affects service compatibility | Cast iron, ductile iron, carbon steel, stainless steel |
| Actuator orientation | Affects installation support | Manual handwheel upward, pneumatic cylinder horizontal |
| Pipe position | Affects physical orientation | Horizontal pipe, vertical pipe, hopper outlet |
| Drawing / tag / P&ID | Confirms project direction | Valve tag, line number, flow arrow, GA drawing |
| Installation constraints | Affects orientation and access | Limited headroom, vibration, support limits |
When to Request Application Review
Request a technical review when:
- the valve is unidirectional and reverse pressure is possible;
- the body arrow and pipeline flow arrow appear to conflict;
- the “SEAT” marking is not clear;
- the valve will be installed horizontally or with a heavy actuator;
- slurry, solids, pulp, wastewater or tailings are present;
- the valve is used for pump isolation, hopper discharge or dead-end service;
- the project drawing does not clearly show pressure direction.
For specification support, provide the flow direction, pressure direction, seat type, valve tag or drawing, intended installation orientation and service media. NTGD can help review whether a unidirectional or bidirectional knife gate valve is more suitable for the application.
FAQ About Knife Gate Valve Flow Direction and Installation Direction
Do I really need to check flow direction before installing a knife gate valve?
Yes. Many knife gate valves, especially unidirectional designs, require flow direction, seat side and pressure direction to be checked before installation. Even when the valve appears symmetrical, the seat arrangement may not be symmetrical.
Can a knife gate valve be installed in either direction?
Not always. A bidirectional knife gate valve may be suitable for flow or pressure from either side under specified conditions. A unidirectional knife gate valve usually requires direction confirmation before installation.
What does seat side mean on a knife gate valve?
Seat side means the side where the valve seat or sealing side is located or marked. It is often identified by “SEAT” or “SEAT SIDE” on the valve body. It should be checked together with the body arrow, pressure direction and IOM manual.
Should the SEAT side be upstream or downstream?
Do not use one universal rule. For some valve designs, the seat side may be specified downstream or on the lower-pressure side. For other designs or applications, the preferred orientation may differ. Always confirm with the valve drawing, datasheet and manufacturer instructions.
What does the arrow on a knife gate valve mean?
The arrow on a knife gate valve body does not always indicate the normal pipeline flow direction. It may show the recommended pressure direction during shutoff, the seat-side orientation or a manufacturer-specific installation guideline. Always check the arrow together with the SEAT marking, datasheet and IOM manual.
What happens if a knife gate valve is installed backwards?
Possible results include seat leakage, poor shutoff, gate not seating, high operating torque, gate or seat wear, packing stress, actuator side load, solids accumulation and premature valve problems. The actual risk depends on valve design and service conditions.
Can a knife gate valve be installed horizontally?
Some knife gate valves can be installed in horizontal or inclined positions, but actuator support, stem orientation, gate alignment and solids behavior must be checked. A horizontal installation should not be assumed acceptable without the IOM manual or installation drawing.
Is a bidirectional knife gate valve completely direction-free?
Not always. Bidirectional shutoff means the valve can seal from both directions under specified conditions. In slurry service, dead-end pressure, reverse pressure or heavy-actuator installations, preferred direction and physical orientation may still matter.
What should be checked before installing a unidirectional knife gate valve?
Check the body arrow, SEAT or SEAT SIDE marking, valve tag, datasheet, IOM manual, P&ID flow arrow, normal flow direction, closed-valve pressure direction, reverse pressure possibility, seat type and installation orientation before installation.
Conclusion
Knife gate valve flow direction should not be decided by a single arrow or by general valve experience. For a reliable installation decision, check the body arrow, SEAT marking, seat side, pressure direction, valve design, normal flow and physical orientation together. This is especially important for unidirectional knife gate valves, slurry service, reverse-pressure conditions and installations with large or heavy actuators.
A good direction review before installation can help avoid leakage, poor shutoff, high operating torque, seat wear, actuator side load and commissioning rework. When the markings, drawings or process conditions are unclear, confirm the application before final valve selection or RFQ.